Announcement

Collapse
No announcement yet.

Search

Collapse
8 results in 0.0189 seconds.
Keywords
Members
Tags
  • You can also choose from the popular tags.

Anet A8 x

  • GDIT
    started a topic A8 hits X & Y limits without halting - Z limit is fine
    in Anet

    A8 hits X & Y limits without halting - Z limit is fine

    I select AUTO HOME and the printhead moves to the left, hits the limit switch, but does not stop. In about 2 seconds of trying to go farther left it stops. It then starts on the Z axis and hits the limit switch correctly and then goes up a bit and then settles as it should. I also have an issue with the Y axis that does not register the limit switch. I ohmed out all 3 limit switches to the end of the cable and all are fine and all connections are correct. I Reloaded the original firmware with...
    See more | Go to post

  • rewsenj
    started a topic Anet a6 not turning on

    Anet a6 not turning on

    I decided to build an enclosure for my Anet a6 to improve the quality of my prints and it has been working fine for a day or two, but now when I plug in the printer nothing happens and the power supply makes a buzzing sound.
    If anyone has any idea what has happened or how to fix it I would really appreciate it if you could tell me
    (not an a8 but they are similar enough)
    See more | Go to post
    Last edited by rewsenj; 04-07-2018, 03:25 PM.

  • 3D Printing Neophyte with an Anet A8

    Hi, all. 3D printing newbie, here. I just assembled my Anet A8 kit this weekend, and got surprisingly good results from my first test print.

    I noticed during my pre-assembly electrical check that Fan 2 (the one with the heat sink) runs constantly. Is this correct, or something up with my controller?


    Thanks,

    R
    See more | Go to post
    Last edited by Admin; 03-05-2018, 08:11 PM.

  • Devil3D
    started a topic Anet A8 - SD card error
    in Anet

    Anet A8 - SD card error

    Hi all,
    last week I've bought an Anet A8. After a few upgrades it's printing quite well (belt tensioners, antiwobble with ball bearings, fan duct, and mosfets boards).

    But it is giving me a strange behavior, it cant read SD card.
    In the logs, it tells me "SD init fail",
    if I try to mount using display menu', nothing happens except... that it starts extruder fan for about 2 seconds!
    I've already tested different cards, but same result.

    Please,...
    See more | Go to post
    Last edited by Admin; 02-09-2018, 10:05 PM.

  • matejc
    started a topic Anet A8 extrudot going to oposite way after few minutes
    in Anet

    Anet A8 extrudot going to oposite way after few minutes

    Hello,

    i got my first 3d printer, Anet A8, and I was abla to print few test models.
    But now, when printer start printing, is ok, but after few minutes, extrudor going to oposite way and again to rigt way. But, because of this, filament is blocked inside and Anet cant fill filament any more. I must clean nozzle throat and start again. But when I start printing again, there is the same problem.... Any hel? Here is video:
    See more | Go to post
    Last edited by Admin; 02-09-2018, 10:05 PM.

  • snoopy20
    started a topic ANET A8 - Auto Levelling Is Rubbish!
    in Anet

    ANET A8 - Auto Levelling Is Rubbish!

    I'm not sure what the fuss is about, the RIKO sensor has too large a tolerance to be accurate and the firmware (at least the standard one) is merely using the the sensor as a replacement for the Z-switch, not profiling the heatbed as I assumed it would. The "Next" step appears to do nothing more than the first step and the Z correction only applies during printing, at which point it may try to center-punch the bed!

    So you still have to set up the bed perfectly level, every...
    See more | Go to post
    Last edited by Admin; 02-09-2018, 10:06 PM.

  • JonnyAlpha
    started a topic Anet A8 or Hictop Prusa i3 ATL II 3DP
    in Anet

    Anet A8 or Hictop Prusa i3 ATL II 3DP

    Hi,
    i am trying to decide between an Anet A8 and a Hictop Prusa i3 ATL 3DP and have some questions.

    The Hictop is an aluminium extruded frame and Auto levelling but I have seen a reviewing saying that the Hot End / Extruder is not good, Blocks.

    Is the Hot End the same part as the Extruder.

    Whats the frame like like on the Anet for rigidity?
    Whats the Hot End and Extruder like on the Anet.
    I have seen some upgrades on auto levelling for the...
    See more | Go to post
    Last edited by Admin; 02-09-2018, 10:06 PM.

  • Admin
    started a topic Anet A8 3D Printer - $139.99 - Coupon Codes
    in Anet

    Anet A8 3D Printer - $139.99 - Coupon Codes



    EU Warehouse
    Coupon: GBA8EU
    Coupon price: $139.99
    Amount: 150
    Link: https://www.gearbest.com/3d-printers...314.html?wid=3

    US warehouse, free shipping
    Coupon: GBA8US
    Coupon price: $139.99
    https://www.gearbest.com/3d-printers...43.html?wid=44


    China Warehouse
    Coupon: A8Forum
    Coupon price: $149.89
    https://www.gearbest.com/3d-printers-3d-printer-kits/pp_337314.html?21
    ...
    See more | Go to post
    Last edited by Admin; 02-09-2018, 10:04 PM.
Working...
X